weld metal
英 [weld ˈmetl]
美 [weld ˈmetl]
焊条金属
双语例句
- The microstructure of weld metal was analyzed with optical microscope and the morphology of joint fracture was observed by SEM.
利用光学显微镜观察分析不同参数条件下接头区域的金相组织； - Research on Organize and Property of Ceramic Phase Strengthening Ferro-base Weld Metal Overlay
陶瓷相增强铁基耐磨堆焊层组织与性能的研究 - Study on the Effect of Alloy Elements on Hot Cracking Susceptibility of Magnesium Alloy Weld Metal
合金元素对镁合金焊缝热裂纹敏感性影响的研究 - Effect of Nb and V in high carbon steel weld metal
铌和钒在高碳钢质焊缝金属中的行为 - Fracture toughness of heat-affected zone ( HAZ) was between the base metal and weld metal.
焊接热影响区的断裂韧性介于母材和焊缝金属之间。 - The impact absorbed energy of weld metal is higher under lower weld porosity ratio.
减少焊缝气孔率可以适当提高焊缝的冲击韧性。 - The deposited ferritic weld metal shall not contact the austenitic or high-chromium steel cladding.
熔敷的铁素体焊缝金属不应与奥氏体或高铬钢复层接触。 - Effect of rare earth oxide on microstructure and mechanical properties of weld metal and its mechanism;
研究了稀土氧化物对人造金刚石用顶锤使用寿命的影响。 - Use a blast cleaner or power tool to remove weld flux slag, weld metal spatters, weld flux fume deposits, rust and damaged paint film in welded areas.
通过喷砂或电动工具除去焊渣、飞溅焊烟、锈迹和焊接部损坏的漆膜。 - Relationship between welding parameter and filling quantity of weld metal in steel bridge welding;
悬索桥钢箱梁桥位焊接施工环境较差，桥位焊接质量、精度控制十分关键。 - Effect of nickel on solidification cracking in low C low alloy steel weld metal
镍对低碳低合金钢焊缝金属凝固裂纹敏感性的影响 - The amount of the acicular ferrite and hardness of the weld metal increase as Cu content increasing.
随着焊缝铜含量的增加，针状铁素体数量增加，焊缝显微硬度增大。 - Superplastic Behavior of Weld Metal by Friction Stir Welding
搅拌摩擦焊接焊缝金属的超塑性行为 - Weld Reinforcement: Weld metal in excess of the quality required to fill a weld groove.
超出质量要求的填充焊缝坡口槽所需的焊缝金属。 - The parameters that deeply effect on the bending strength were porosity, energy input and the overlapping of weld metal.
明显地影响抗弯强度的参数是气孔，输入能量的大小和焊接金属的重叠性能。 - Addition of activating agent has no obvious effect on fracture toughness of weld metal.
添加活性剂对焊缝金属的断裂韧性没有明显作用。 - To simulate the effect of the defect on performance of steel structure, damage evolution law of weld metal must be predefined.
为了模拟这些缺陷的发展对结构性能的影响，需要知道焊缝金属的损伤演化规律。 - Filler rods for gas welding of mild steels and low alloy high tensile steels-Determination of mechanical properties of deposited weld metal
软钢、低合金高强度钢气焊用焊条－－堆焊金属的力学性能的测定 - The application of active infrared technology eal-time and on-line weld metal detection
主动红外技术在实时在线焊缝检测系统中的应用 - A method about improving the crack resistance of weld metal and reducing structure stress during welding process, i.e.hammering welds and watered rapid cooling after welding, was obtained.
研究出了提高焊缝金属抗裂性能及降低焊接过程结构内应力的工艺方法&焊后捶击焊逢并浇水快速冷却。 - The results show that the addition of Zr increases the content of acicular ferrite and improves the microstructure of weld metal.
结果表明，锆的加入增加了焊缝金属中针状铁素体的含量，改善了焊缝金属的微观组织。 - In this paper, the effect of copper content on the weld metal toughness in SAW of HSLA steels was studied by changing the copper content in welding wire.
采用埋弧焊方法，通过改变焊丝铜含量来改变焊缝金属中的铜含量，研究铜对高强度低合金钢焊缝金属韧性的影响。 - Difference of impact absorbed energy between butt weld metal and deposited metal
对接焊缝金属和熔敷金属冲击吸收功差异的探讨 - Effect of laser welding parameters on formation of cold-worked die steel weld metal
激光焊接参数对冷作模具钢焊缝表面成形的影响 - It was also found out that proper Re element addition could increase the toughness of the weld metal and improve its microstructure by grain refinement.
适量的稀土元素可改善焊缝金属组织的形态、细化晶粒、提高韧性。 - Influence of the relative width of weld metal and strength of weld metal wes researched.
研究了焊缝金属相对宽度和焊缝金属强度对接头性能的影响。 - The transformation conditions and natures of acicular ferrite in the weld metal of microalloy steels were analyzed systematically.
系统地分析了微合金钢焊缝金属中针状铁素体组织的形成条件及特点，对夹杂物粒径、数量进行了统计分析，并阐述了针状铁素体的形核位置。 - The fracture behaviour of weld metal of ferrite-austenite duplex stainless steel was investigated by constant deformation rate tensile test.
用恒变形速率拉伸试验方法研究了铁素体奥氏体双相不锈钢焊缝金属的断裂行为。 - By using multi-layer multi-pass welding, weld metal to improve the plasticity, grain refinement of the organization.
通过采用多层多道焊，提高焊缝金属的塑性，细化了组织晶粒。 - Secondary acicular ferrite nucleation, growth, refining the original grain, further improve the weld metal toughness.
二次针状铁素体的形核、长大，进一步细化了原晶粒，提高了焊缝金属的韧性。